Resources / Apex

Installing your Apex

No dealer install, no shop
appointment. Eleven steps, four jacks, and a spotter.

Because the Apex is a slide-in, loading it is the same job whether
you are doing it the day it arrives or the first weekend of every
season. Attach the jacks, lift, back the truck under, strap it down.

Most owners have it done in under an hour the first time, and in
twenty minutes after that. The only part worth slowing down for is
backing under, which is step 03.

Before you start
Work on firm, level ground. Set the parking brake and chock the
wheels before you go behind or underneath the camper. Confirm your
truck’s payload covers the Apex plus gear, water, and passengers.
Two people makes this easier and safer than one.

Watch first

The full install, start to finish

One pass through the whole job, from bolting on the jacks to pulling
out of the driveway. The written steps below cover the same ground if
you would rather read it, or need something to follow with your hands
busy.

External video / map — unavailable in offline demo

01
Setup

Attach the four jacks

Slide a mechanical jack into the dedicated jack mount at each
corner of the Apex and pin it. Seat each one fully before it
takes any load. All four go on before anything comes off the
ground.

Side view of the Apex with a mechanical jack attached at the corner jack mount.
Jacks seat into the dedicated mounts at all four corners
02
Setup

Raise the camper

Jack each corner up until the bottom of the Apex clears your
tailgate and bed floor. Work around the camper a few inches at a
time rather than running one corner to full height, so the load
stays balanced across all four jacks.

Leave yourself extra
Go a little higher than you think you need. Lowering the camper
is easy. Lifting it again with the truck already underneath is
not.
The Apex raised on all four jacks with the floor clear of the truck bed.
Raise a few inches at a time, working corner to corner
03
Alignment

Back the truck under

Slowly back the truck under the Apex until the bulkhead of the
truck is barely touching the front of the camper, or just a hair
off touching it. Use a spotter, go slow, and check both bed rails
as you come back.

A pickup truck backed under the raised Apex with the cab-over positioned above the cab.
Stop when the truck bulkhead is barely touching the front of the camper
04
Before you lower

Run the straps

Before lowering the jacks, attach the included straps through the
existing tie-down points at each corner of the truck bed. Factory
tie-down points work in most cases. Some customers opt for
upgraded truck camper tie-downs, which is worth considering if you
run rough roads or spend a lot of time loaded.

A tie-down strap looped through a factory tie-down point in the corner of the truck bed.
Loop through the tie-down point, then feed both ends to the ratchet
05
Before you lower

Feed the straps into the ratchets

With each strap looped through the bed tie-down point, insert both
ends into the ratchet mount on that corner of the Apex.

  • Front ratchets. Both are on the front wall of the camper, where you can reach them from outside.
  • Rear ratchets. One is under the fridge area, the other under the kitchen area.
A tie-down ratchet mounted on the corner of the Apex with both strap ends fed through it.
Four ratchets: two forward, two aft under the fridge and kitchen
06
Lowering

Lower the jacks

Bring the jacks down slowly, moving corner to corner in small
increments so the camper settles evenly into the bed rather than
landing on one corner first.

07
Lowering

Remove the jacks

Once the Apex is fully down on the bed floor and sitting square,
pull the pins and take all four jacks off. Stow them where they
will not shift in transit.

08
Securing

Tighten the tie-downs

Work the four ratchets down in an even pattern, alternating side
to side and front to back. Snug and firm is the target.
Overtightening puts unnecessary load on the bed and on the camper
frame, and it does not make the camper any more secure.

09
Electrical

Connect the lighting harness

Plug in the wiring harness for the running lights and the rear
brake light, then test both before you pull out. Route the lead
clear of the tailgate and the strap paths.

10
Electrical

Connect the DC-DC charger

If your Apex is equipped for a DC-DC charger, connect the Anderson
connector at the front of the camper to the truck side connector.
The camper battery then charges any time the vehicle is running.

11
Done

Go camping

Walk the camper one more time. Four straps tight, jacks stowed,
both connectors seated, lights working. Then go.

Once you are loaded

The first twenty miles

Straps settle as the camper seats into the bed, which means the
tension you set in the driveway is not the tension you have on the
highway. Pull over after the first 20 to 30 miles and take up the
slack, then check them again at the start of every trip.

  • Recheck all four ratchets after the first 20 to 30 miles
  • Check them again each morning on a long trip
  • Confirm the lighting harness is seated before every drive
  • Keep the jacks and pins together, stowed where they cannot move

Tie-down hardware and bed dimensions vary by truck make, model, and
bed length. If anything on this page does not match what you are
looking at, stop and ask us before you load it.

Not sure about your truck?

Send us your year, make, model, and bed length and we will tell you
exactly what your Apex needs, including whether upgraded tie-down
points are worth it for how you use it.